If you're looking to give your ATV extra pulling power by increasing torque then a gear reduction kit is the way to go!While an ATV may be a great performer on the trail with stock tire height, when larger mud tires are added for use in extreme conditions this can often leave a performance enthusiast wishing for more low end grunt. You can overcome this problem by using a gear reduction kit. A reduction kit is designed so that a stock ATV can turn the larger more aggressive mud tires without additional costly engine modifications. Once you install a gear reduction kit the motor doesn't have to work as hard to spin the tires which means it won't draw as much current from your batteries while it simultaneously increases torque to provide you with the traction and pulling power that you need.The system requires approximately 4-5 hours of labor by an experienced technician to install and is furnished complete with pictures and instructions. After installation, the RPM will be slightly increased, even with oversized tires. Tests have shown this increased RPM has not been objectionable. Gas mileage is essentially the same as the machine would get without the gear reduction system and with oversize tires installed. This product is carefully machined and heat treated for durability and long life. 28 percent reduction
REAL VALUE. REAL COLD. One-piece, roto-molded construction for extreme toughness and durability.Constructed of food-grade material that is UV resistant and DryIce compatible.K2’s SNOWblown™ insulation is injected under extreme pressure, ensuring you get proper insulation for maximum ice retention.The K2 ICEvault™ gasket is designed and installed to lock in the cold and keep the heat out. Partnered with the LOCKaway™ lid design your K2 will keep your contents ice cold or steaming hot as well as protect them from the outside elements.The Summit 20 features a nylon strap with a cushioned shoulder piece making its portability truely grab-n-go!The POSITRAC™ lid latches are designed to create a positive seal and are mounted on molded-in keepers for that perfect closure every time.The ENDURA™ hinge system is a full length integrated hinge that is designed to keep your lid permanently attached.Our SUREgrip™ rubber feet are non-marking and designed to keep your cooler exactly where you put it. You can add SMOOTHglide™ covers to them which will allow the cooler to slide easily.The bottom line is no matter your activity, hunting, fishing, boating, camping, rafting, tailgating or just enjoying a day at the beach or a backyard barbeque — you won’t be disappointed by the ice retention or reliability of your K2 cooler
The '09 Honda Rancher A/T IRS is factory equipped with a 420cc four stroke, 24" tires, 6.3" of suspension travel front and rear and 9.1" of ground clearance. Xtreme Products' 1" lift creates room for up to 28" tires. That combination provides 3" of total lift height and 12.1" of total ground clearance. Get the most out of your Rancher with the Xtreme Products 1" lift today. (Relocates top of Front shocks and bottom of Rear shocks w/brackets).Xtreme Products lift kits are designed to provide maximum performance, durability, and enhance handling and stability characteristics while keeping installation simple and easy. Our designs help stabilize the suspension and make your ATV more sure-footed over rough terrain. Xtreme Products atv lifts provide the maximum lift available without causing costly damage to axles and related drive train components. Trail friendly lift systems built to get you in and OUT of the deep stuff.All Xtreme Products lift kits are precision engineered using A36 3/16 or 1/4 inch cold roll steel for maximum strength and reliability. Parts are laser cut then manufactured to exacting tolerances to provide the best value available. All Xtreme products are backed by a Limited Lifetime Warranty.
High Lifter Lift Springs are a set of higher capacity replacement springs which are components of the stock shock absorbers. The original equipment spring is not heavy duty and is often fatigued early by heavy loads or continuous service. OEM springs tend to fatigue rapidly...even with low mileage.The High Lifter Lift Springs were engineered to provide about 100 additional pounds of capacity (per set) over the new stock springs. They were also designed to make a significant difference in the performance of your ATV with as little affect as possible on the ride and handling of the machine. The Lift Springs add some stiffness to the ride and decrease roll, but have not been found harsh or uncomfortable by anyone who has ridden them.And here's a big bonus! A complete set of the Lift Springs may be installed for substantially less than the cost of one replacement OEM shock. For those who ride at slower speeds, with big tires and heavier loads, the Lift Springs will be a welcome and economical upgrade.Depending on the make and model...and current modifications to the unit, the High Lifter Lift Springs have been known to add on full inch of suspension lift...however, it's not guaranteed. The Lift Springs add some stiffness to the ride and decrease roll, but have not been found harsh or uncomfortable by anyone who has ridden them.One thing is for sure. If you are a hardcore mud rider...or you carry a load...your ATV could stand a heavier load capacity. The High Lifter Lift Springs are just what the doctor ordered!APPLICATIONS:Honda 420i Rancher IRS 2009Front & Rear spring kit